If you have a paddock that needs topping, harrowing, spraying or a hedge cut, you probably know the usual routine. You post in a local Facebook group: "Anyone recommend someone to top 4 acres near Romsey?" Then you wait.
Some replies come in. A few are tagged names, a few say "PM'd you", one is a friend of a friend who "might be able to fit you in". Then the real work starts. You message each one, describe the field again, send the same photos again, wait for answers, chase the ones who go quiet, and try to compare a price per hour with a price per acre with a "call me and we'll sort something".
It works, eventually. But it is slow, and it tends to leave money on the table. Here is why, and what we do instead.
The problem with the Facebook group method
You do all the legwork. Every contractor has to be contacted, briefed and chased one at a time. Five replies means five separate conversations.
You only hear from whoever happens to be scrolling. A post reaches the people in that group who see it that day. A good contractor ten miles away who is not in the group, or was out on a tractor all afternoon, never finds out about your job.
The first answer is not the best answer. When chasing prices is hard work, most people stop after one or two and book whoever replied first. As the numbers below show, the first price is very often not the cheapest one.
The prices are hard to compare. One quote is by the hour, one is a day rate, one is a figure given over the phone that you have to remember. Nothing is side by side.
What happens when you post a job with us
You describe the job once: what needs doing, where the field is and roughly how big it is. You can draw the field on a map if you like.
We send it to the contractors whose coverage includes your area. The network has 537 vetted contractors across all 99 UK counties, so your job reaches people who would never have seen a Facebook post in your village group.
Contractors look at the job and send their prices back through the site. You do not have to contact anyone or repeat yourself. Each price arrives in the same place, as a figure for your job, alongside the contractor's rating and how far away they are. If a contractor needs to see the site before they can commit, the price says so.
You can message a contractor if you have a question, pass on a price you do not want, and accept the one you do. Nothing is booked until you accept, and there is no obligation to go ahead at all.
Is it actually quicker?
We looked at the 130 jobs sent out to contractors between our launch on 6 September and early November 2026.
- Half of the jobs that got a price got their first one within about an hour and ten minutes. A quarter got one within seven minutes.
- Three quarters of priced jobs had their first price within 24 hours.
- 78% of jobs got at least one price, and priced jobs got three prices on average. 46 jobs got three or more.
Compare that with a Facebook post on a Tuesday evening, followed by a week of messaging.
Does it get you a better price?
This is where having several prices side by side matters most. We took the 54 jobs that received two or more fixed prices (leaving out hourly rates and prices that depended on a site visit, so we were comparing like with like).
- In 39 of the 54 jobs, nearly three in four, the first price to arrive was not the cheapest.
- For the typical job, the cheapest price was about a third lower than the first one, a difference of around £220.
- The highest price on a job was typically more than twice the lowest.
Those gaps are not about cowboys and bargains. Contractors price differently depending on how far they have to travel, what kit they have, how busy they are and whether they can fit your job in alongside others nearby. You only see that spread if you get several prices for the same job, and getting several prices is exactly the part that is hard work on Facebook.
Cheapest is not always best, of course. You can see each contractor's rating and distance before you choose, and you can ask questions first. The point is that you get to make the choice with all the options in front of you, not just the first one that turned up.
A few tips to get the most out of it
- Be specific about the job. "Top 4 acres of rough grass, last cut in June, gate access off a lane" gets firmer prices than "paddock needs doing".
- Give the size, or draw the field. Most paddock work is priced by area, and a map boundary saves the back and forth.
- Mention access and obstacles. Narrow gates, soft ground, ditches, fencing, livestock and anything that should be left alone.
- Say when you need it done. A flexible date can bring the price down, because a contractor can fit you in when they are already working nearby.
- Give it a day. Most prices come quickly, but the cheapest is not always the first, so it is worth waiting for a few to arrive before you choose.
Get prices for your paddock
Tell us about your field. It takes a couple of minutes, it goes to the contractors who cover your area, and the prices come to you. No chasing, no repeating yourself, and no obligation to go ahead.
To see what other people have paid, have a look at real paddock topping prices, paddock weed spraying prices and cost per acre by county.
Quick answers
How do I find a contractor to top my paddock? You can ask around or post in a local Facebook group and contact each reply yourself, or you can post the job once with us and contractors who cover your area send you their prices.
How long does it take to get a price? Across 130 jobs in autumn 2026, half of priced jobs had their first price within about 70 minutes, and three quarters within 24 hours.
Should I take the first price I get? Usually it pays to wait for a few. In nearly three in four of the jobs we looked at, the first price was not the cheapest, and the cheapest was typically about a third lower.
Does it cost anything to post a job? No. Posting a job and receiving prices is free, and there is no obligation to accept any of them.


